Impact garage doors
Single hung
Double hung
Horizontal roller
Casement
Bay & bow
Sliding glass doors
Entry doors
PGT
CGIFree in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Get your free estimateMr-Glass Impact Garage Doors: The Sunrise Manor Owner’s Guide
We install and service Mr-Glass-compatible impact garage doors in Sunrise Manor, and a full door replacement typically runs $2,400 to $5,800 installed, depending on size, wind-load rating, and whether the opening needs new tracks or a heavier torsion system. Single-car doors land near the low end; double-car impact doors with reinforced hardware sit at the top. Most part-level failures we see, spring, roller, hinge, and bottom seal, are handled on a scheduled visit, not the same day. Owners usually discover the problem the first morning the door won’t reverse, or when a roller starts grinding loud enough to hear from the kitchen.

Which Mr-Glass Models This Applies To
Mr-Glass builds impact-rated doors for Florida and coastal wind zones, and those same doors show up on plenty of Sunrise Manor homes where windborne debris and summer heat are the worry. The parts inside them are not universal. Spring wire gauge, drum size, and hinge spacing vary between the single-car and double-car lines, and a hinge that fits one panel thickness will bind on another. Before we quote anything, we read the sticker on the inside of the top panel, which lists the model and wind-load rating, and we measure the door’s width, height, and panel thickness. That label is the difference between a part that lasts and one that fails in a year.
On the OEM-versus-aftermarket question: for springs and torsion hardware on an impact door, we lean OEM or a rated equivalent matched to the door’s wind-load class, because an under-rated spring on a door built to hold against debris load is a real safety issue. Rollers, hinges, and bottom seals have solid aftermarket equivalents that cost less and hold up fine in Nevada heat. We’ll tell you which is which on the quote.
We’re an independent service provider. We’re not affiliated with Mr-Glass, and we don’t claim to be. We’re an authorized installer of Mr-Glass doors, along with PGT, CGI, and CWS products.
Styles & brands we work with
- Single hung
- Double hung
- Horizontal roller
- Casement
- Bay & bow
- Sliding glass doors
- Entry doors
- Impact garage doors
- PGT
- CGI
Signs Your Mr-Glass Impact Garage Doors Is Failing
- The door slams down instead of easing shut. A torsion spring has lost tension or snapped. On impact doors the springs are sized heavier than a standard door, so a failed spring lets a very heavy panel drop fast.
- A visible gap or sag along the bottom seal. The seal has dried and cracked from the desert sun and heat cycling. Left alone, it lets dust, heat, and pests in, and the door loses its weather seal.
- Grinding, squealing, or a rhythmic thump as the door moves. Worn steel rollers or a dry, failing bearing. Nylon rollers quiet down; steel ones pit and grow loud.
- The door binds or pulls away from the track on one side. A bent hinge or a track knocked out of plumb. Impact doors are heavier, so a small misalignment wears the hardware faster.
- The opener strains, reverses, or the door won’t stay up halfway. The torsion system is out of balance, or the spring is on its way out. This one is a warning, not a nuisance.
Nevada heat is hard on these parts. We regularly see bottom seals and steel rollers fail in Sunrise Manor within a few summers, well before the door itself is anywhere near done.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Part-level repairs in Sunrise Manor generally run $180 to $650, depending on what failed and whether it’s one part or a set. Torsion spring replacement for an impact door typically lands $280 to $480 per spring, because the heavier wire costs more. Roller and hinge sets run $180 to $320. Bottom seal replacement is $160 to $280. A full door replacement, if the panels themselves are compromised, is $2,400 to $5,800 installed. What drives the range: door size, wind-load rating, spring wire gauge, and whether the tracks or opener need work too.
Every quote is line-itemed, parts and labor broken out, so you see exactly what you’re paying for. Our repair work carries a workmanship warranty, and we stand behind it under our 36500-Day Done Right Promise. If it’s not done right, we make it right.

DIY or Call Us?
Some checks are safe. You can look at the bottom seal for cracks, watch the door travel to spot a bind, and listen for grinding. You can also test the balance: pull the release and lift the door halfway by hand. If it won’t hold, the spring or torsion system is the problem.
What you should not touch is the torsion spring and the cables. Those parts are under extreme tension, and an impact door’s springs carry more load than a standard door’s. A snapped spring or cable can cause serious injury, and there’s no safe way to work on them without the right tools and training. This is the one part where we tell every Sunrise Manor homeowner plainly: leave it to a trained technician. Our technicians have up to 15 years of experience, and every one is background-checked and arrives in uniform.
For a spring, cable, or torsion issue, call us at (844) 761-9603. A live person answers, day or night, and we’ll schedule a visit and give you an upfront price before any work starts.
FAQs
Torsion springs on these doors typically last 7 to 12 years under normal use, but Nevada’s heat and daily cycling push many toward the short end. Bottom seals and steel rollers often fail in 3 to 5 years here. Nylon rollers and a properly balanced door extend that.
Often, yes. A single worn roller, a bent hinge, or a cracked bottom seal is a straightforward repair. A snapped torsion spring is a replacement, not a repair. We’ll tell you honestly which you’re looking at before we quote.
Most part-level repairs take one to two hours on site. A full door replacement is a longer scheduled job. We’ll give you a realistic time window when you book, not a vague “sometime today.”
We match the part to your door’s model label and measured dimensions. For springs and torsion hardware we use OEM or a rated equivalent matched to your door’s wind-load class. For rollers, hinges, and seals we’ll recommend a quality aftermarket option when it makes sense, and say so on the quote. We don’t claim to stock parts or carry them on a truck; we source what your door needs.
If your Mr-Glass impact garage door is binding, slamming, or just not sealing like it used to, call (844) 761-9603 for a free estimate. We’re the one down the road, and Ed’s name is on the door and on every job we do. Seniors and veterans get a permanent 10% discount, and we’re glad to give a free second opinion on any written estimate you already have.
Written by the team at Winslow Windows & Doors Sunrise Manor, serving Sunrise Manor and nearby areas.